Tyco B0 Manual do Utilizador

Part Number: 8200-2646-00 B0 VideoEdge IP Box CameraInstallation & Operation GuideVersion1.5

10 Installation and Operation Guide Dimensions / Weight Dimensions and weight are as follows. ‧Height: 55 (mm) ‧Width: 95 (mm) ‧Length: 62 (mm) ‧We

Installation and Operation Guide 11 2. DESCRIPTION OF THE FRONT/REAR VIEW 2.1 Front Panel and Rear Panel -- Front Panel -- -- Rear Panel -- 12345

12 Installation and Operation Guide 2.2 Flank Panel -- Left Flank Panel -- -- Right Flank Panel -- 123456 7 1. Lens Mount: This IP camera is used w

Installation and Operation Guide 13 Alarm wiring diagram: 4. RESET: Recover to factory default. 5. 5pin MINI USB Port: The user can use a USB dev

14 Installation and Operation Guide 2.3 The USB function By connecting the IP camera with a PC via the USB connector, the IP camera can provide two

Installation and Operation Guide 15 2.4 Bracket mount installation The underside of the camera has a screw hole for attaching the bracket to the c

16 Installation and Operation Guide 3. INSTALLATION Please follow the instructions and the diagram below to set up the system. NOTE: The IP camera

Installation and Operation Guide 17 3.3 CONNECTING WITH A MULTIPLEXER LAN CAMERA 1LAN CAMERA 2LAN CAMERA 16TO LAN CAMERA VIDEO OUT BNC CONNECTOR 3

18 Installation and Operation Guide If the message "UPDATE NG RESET PLEASE" appears rather than "UPDATE OK RESET PLEASE", please

Installation and Operation Guide 19 3.5 IP camera SD card Troubleshooting 1. Check if the SD card position is correct or not. Please refer to the

20 Installation and Operation Guide 4. Network Configuration 4.1 Cable Connections Please follow the instructions below to connect your IP camera t

Installation and Operation Guide 21 4.1.2 Connect to a LAN Hub (INTRANET) The RJ-45 PIN configuration for connecting with a LAN Hub is shown below.

22 Installation and Operation Guide 4.2 Configure Your IP Camera Network Settings Upon connecting with the network hardware, you need to activate th

Installation and Operation Guide 23 NOTE: When connecting to a network, each connected IP camera must be assigned a unique IP, which must be in the

24 Installation and Operation Guide 4.3 TCP/IP Communication Software Follow the procedure below to install the TCP/IP communication program in your

Installation and Operation Guide 25 components list. If the TCP/IP is included, please process section 4.5. If it is not included, please follow sec

26 Installation and Operation Guide 2. Select TCP/IP, and then click Properties. NOTE: Before processing the IP camera installation in a WAN, pleas

Installation and Operation Guide 27 4.6 Connection Testing With the previous settings, follow the instructions below to ensure whether you have esta

28 Installation and Operation Guide If you receive a response as in the sample screen below, the connection hasn’t been successfully established. Pl

Installation and Operation Guide 29 5. Operation Instructions for the Network The Microsoft Internet Explorer in a PC provides the functions of mon

Copyright Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced, translated or reduced to any el

30 Installation and Operation Guide 5.1 Microsoft Internet Explorer 5.1.1 Connecting the IP camera 1. Start up Microsoft Internet Explorer, and

Installation and Operation Guide 31 Browsing images from the IP camera The images from the IP camera are displayed on the home page when online with

32 Installation and Operation Guide 5.1.2 Change Video Setting Please follow the steps below to change the image setting through the network as nec

Installation and Operation Guide 33 5. Click on the Privacy Mask button to enter the Privacy Mask page. 6. Click on the Day & Night button t

34 Installation and Operation Guide to set the period of the focus adjustment at “30 seconds”, “1 minute”, “2 minutes”, “3 minutes”, “5 minutes”, an

Installation and Operation Guide 35 Frame rate: Click on the drop-down list to choose the frame rates of “5FPS”, “10FPS”, “15FPS”, “24FPS” or “(25)

36 Installation and Operation Guide 5.1.3 Change the Network Setting Please follow the steps below to change the network setting through the networ

Installation and Operation Guide 37 Description of function keys: IP Address: Enter the 4-byte IP Address in the appropriate blank space (the valu

38 Installation and Operation Guide  Change the Network Setting — FTP (MJPEG mode only). Please follow the steps below to change the FTP setting v

Installation and Operation Guide 39  Change the Network Setting — SMTP (MJPEG mode only). Please follow the steps below to change the SMTP setting

4 Installation and Operation Guide Table Of Contents SAFETY PRECAUTIONS ...

40 Installation and Operation Guide  Change the Network Setting — SNTP. Please follow the steps below to change the SNTP setting through the netwo

Installation and Operation Guide 41  Change the Network Setting — DDNS. The “Network” page has, on its upper left, the “DDNS” icon. Please follow

42 Installation and Operation Guide Description of function keys: Enable DDNS Function: Checkmark to activate the function. DDNS Type: Click to ope

Installation and Operation Guide 43  Change the Network Setting — PPPoE. The “Network” page has, on its upper left, the “PPPoE” icon. Please follo

44 Installation and Operation Guide  Change the Network Setting —UPnP. The “Network” page has, on its upper left, the “UPnP” icon. Please follow t

Installation and Operation Guide 45  Change the Network Setting — IP Filter The “Network” page has, on its upper left, the “IP Filter” icon. Pleas

46 Installation and Operation Guide  Change the Network Setting —Network Traffic. The “Network” page has, on its upper left, the “Traffic” icon. P

Installation and Operation Guide 47 5.1.4 Change the System Setting Please follow the steps below to change the date and time of the system setting

48 Installation and Operation Guide  Change the System Setting — Timestamp. Please follow the steps below to change/add the timestamp through the

Installation and Operation Guide 49  Change the System Setting — Users. Please follow the steps below to change/add the users’ authority through t

Installation and Operation Guide 5 4.5 TCP/IP CONFIGURATION SETTING ...25 4.6 CONNECTION TESTING.

50 Installation and Operation Guide  Change the System Setting — Digital I/O. Please follow the steps below to change the Digital I/O through the

Installation and Operation Guide 51  Change the System Setting — Audio. Please follow the steps below to change the Audio setting through the netw

52 Installation and Operation Guide  Change the System Setting — RS485 Setting. Click on the RS485 Setting button on the left side of the “Date an

Installation and Operation Guide 53  Change the System Setting — Update Firmware. Please follow the steps below to update the firmware through the

54 Installation and Operation Guide  View the Event Logs. Please follow the steps below to view events through the network as necessary. 1. Click

Installation and Operation Guide 55 5.1.5 Change the Application Setting Please follow the steps below to change the application setting through th

56 Installation and Operation Guide  Change the Application Setting — SD Card Application Setting. Please follow the steps below to change the SD

Installation and Operation Guide 57  Change the Application Setting —SMTP Application Setting (MJPEG mode only). Please follow the steps below to

58 Installation and Operation Guide  Change the Application Setting —Language Setting. Please follow the steps below to change the Language settin

Installation and Operation Guide 59  Change the Application Setting —Record Application Enable Setting. Please follow the steps below to change th

6 Installation and Operation Guide SAFETY PRECAUTIONS All the following safety and operational instructions to prevent harm or injury to the operator

60 Installation and Operation Guide  Change the Application Setting —Record - Schedule. 1. Click on the Application button on the home page to en

Installation and Operation Guide 61  Change the Application Setting — Alarm Application Enable Setting. Please follow the steps below to change th

62 Installation and Operation Guide  Change the Application Setting — Alarm - Motion Detection. Please follow the steps below to enable changes in

Installation and Operation Guide 63 5.1.6 Change the SD card Setting Please follow the steps below to change the SD card setting through the networ

64 Installation and Operation Guide 5.1.7 Change the Pan/Tilt setting 1. Click on the Pan/Tilt button on the home page to open the Speed Dome Cont

Installation and Operation Guide 65 5.1.8 PPPoE & DDNS Using the PPPoE 1. Install the XDSL software (obtained from your ISP dealer) in your P

66 Installation and Operation Guide Test: Go to the Internet. 1. Set your PC to enter the Internet. 2. Desktop → IE browser → Enter the IP camera

Installation and Operation Guide 67 5.1.9 The Bandwidth Calculator of the IP camera You can use the calculator to obtain the rough bandwidth throug

68 Installation and Operation Guide 6. ADVANCED OPERATION Question 1: How can I view the live images of the IP camera via Microsoft Internet Explore

Installation and Operation Guide 69 3. Check on “Enable Alarm-Save into SD Card” to activate it. 4. Click the Submit button to submit the setting. N

Installation and Operation Guide 7 1. PRODUCT FEATURES 1.1 Product Instructions The VideoEdge IP Box Camera ADCIPEB is a user-friendly device which

70 Installation and Operation Guide ◇Set the PPPoE function 1. Click the Network button in the home page. 2. Click the PPPoE button on the left side

Installation and Operation Guide 71 7. SPECIFICATIONS ADCIPEBN VideoEdge IP Box Camera, 24VAC/12VDC, NTSC, w/PS ADCIPEBPE VideoEdge IP Box Camera,

72 Installation and Operation Guide Video output 1.0 Vpp, 75 ohm, composite, negative, BNC x 1 Alarm I/O 1 input / 1 output Serial port RS-485 SD

Installation and Operation Guide 73 APPENDIX 1. –IP camera UPnP How To The most troublesome issue when you setup a LANCam® is that you have no idea

74 Installation and Operation Guide Figure 2 Step 2: When Control Panel appears, double-click the Network Connections icon. The Network Connectio

Installation and Operation Guide 75 Figure 5 Step 5: In the Internet Protocol(TCP/IP) Properties dialog box, choose Use the following IP Address t

76 Installation and Operation Guide 2. Install UPnP Packets As described before, Microsoft Windows XP® doesn’t start the UPnP service by default; h

Installation and Operation Guide 77 Figure 10 Step 4: Check UPnP User Interface, and choose OK. See Figure 11. Figure 11 Step 5: When the orig

78 Installation and Operation Guide Step 6: After about one minute the UPnP installation will be done, and choose Finish to close it. See Figure13.

Installation and Operation Guide 79 Figure15 Step 3: Click on the Services icon in the Administrative Tools dialog box. See Figure16. Figure16

8 Installation and Operation Guide 1.2 Product Features • 1/3" SONY Super HAD CCD. • Mechanical IR Cut Filter. • MPEG4 / MJPEG video compres

80 Installation and Operation Guide Figure17 Step 5: Choose Automatic in the Startup type, and click OK to start it. See Figure18. Figure18

Installation and Operation Guide 81 Figure19 Step 7: Choose Automatic in the Startup type, press the Start button, and click OK to start it. See

82 Installation and Operation Guide 4. Scan LANCams® through My Network Place After your installation and starting services, the UPnP protocol will

Installation and Operation Guide 83 APPENDIX 2. –The ARP function Setting the IP Address The Ethernet interface on the LANCam has a default IP add

84 Installation and Operation Guide ARP and ping from UNIX or GNU/Linux: 1. Start a shell 2. Type the following as superuser (root): arp -s <

Installation and Operation Guide 85 APPENDIX 3. –Register as a DDNS member The DDNS（dynamic domain name system） is a function which is provided by a

86 Installation and Operation Guide Figure 2 Figure 3 Click “My Services” to enter the service page. Please click the “Add Host Service” item whic

Installation and Operation Guide 87 Figure 4 Figure 5 All we have to set in this page is the “Hostname” item. The user can choose a Sub Hostname

88 Installation and Operation Guide Figure 6

Installation and Operation Guide 89 APPENDIX 4. –MPEG4 Bit Rate Lookup Table of IP camera 1. When frame rate is higher than 15 frames/second (15 is

Installation and Operation Guide 9 Image: ‧Image frame rate: up to 30 (25) frames/second. ‧Supports two compression modes, the Motion - JPEG and the

90 Installation and Operation Guide APPENDIX 5. –FAQ 1. How do I disable the DHCP function and use a static IP instead? A：Turn up the “DIP SWITCH”